122-39(SD)注射器用導熱環氧模貼膠

說明：122-39（SD）是一種注射器，可有可無，導熱，電絕緣，單組分，

100%固體環氧粘合劑。該系統具有優異的熱穩定性、優異的耐化學性和

優異的高溫性能。應用包括與鍍金基板和錫/鉛焊料的粘合

端接元件、模具連接和熱管理操作、印刷電路板制造、高級

材料復合，密封和高性能涂層。122-39（SD）是122的導熱型-

38（標準差）。

屬性：

粘度（cps）40000

觸變指數>2.5

填料氮化鋁

填料百分比60

大體積電阻率（Ω-cm）1 x 1016

熱導率（w/mk）3.5

介電常數（1kHz）4.1

介電常數（1MHz）3.9

損耗因子（1kHz）0.027

損耗因子（1MHz）0.038

有效溫度范圍（℃）-55至+250

熱穩定性（℃）良好至+300

模具剪切強度（psi）>2200（0.09“x 0.16”模具）

搭接剪切強度（psi）>2200

玻璃化轉變溫度，tg（℃）91

科夫。熱的。實驗溫度低于tg（ppm/℃）75

高于tg（ppm/℃）233

離子含量

氯化物<10 ppm。

鈉<10 ppm。

鉀<10 ppm。

（典型特性不用作規范限值。）

建議的處理和固化：材料在收到后即可使用。存儲凍結以保持*

流動特性。打開容器前，讓材料預熱至室溫。使用前混合

如果包裝在容器中，容器應重新懸掛填料。在150℃下固化60分鐘，或在

175攝氏度。

貯存期：在25℃下保存<4天；在-10℃下保存6個月；在-40℃下保存12個月。

安全和操作：在通風良好的情況下使用。遠離火花和明火。避免

長時間接觸皮膚和吸入蒸汽。用肥皂和水清洗皮膚。

通過ISO 9001認證

創意材料公司

所有技術信息均基于CMI人員獲得的數據，并被認為是可靠的。沒有保證是

關于結果或可能侵犯的明示或暗示的。

修訂日期：03/03/17修訂日期：E

注射器操作指南

存儲：

•收到貨物后，應立即打開注射器的包裝，并將其存放在-10°C的冰箱中。

不要將注射器保存在深度冷凍（-40°C）中。

•不要從包裝主體處處理注射器。從包裝的末端處理。

•垂直（直立）存放注射器，針頭朝下。不要水平（側面）存放注射器。

注射器應以這種方式儲存，直到生產需要。注射器的保質期

在產品技術數據表上。

•注射器標有產品編號、批號和生產日期。重要的是

注射器按早生產日期“先出”使用。

準備使用注射器：

•要解凍注射器，請將其從冰箱中取出，注意不要接觸注射器主體（手柄

從頂部和/或頂部），并允許他們適應環境溫度與頂部向下。

•不要用手加熱注射器。

•每個注射器的解凍時間將根據質量和成分而變化，但至少為45分鐘

對于3cc、5cc和10cc，應至少觀察90分鐘，對于30cc注射器。

•不建議使用熱源解凍注射器。

在融化過程中接近熱源應大于3英尺。

•盡管大多數材料可以重新冷凍，但建議盡量減少凍融循環。

•一旦材料*解凍，移除保護性包裝。

注射器信息：

•創新材料注射器配有Luer鎖緊裝置，與大多數配藥類型兼容

設備。

•創新材料注射器采用光滑流動活塞技術設計，用于

自動或手動分配設備，但未配備手動柱塞。

•創意材料通常提供3cc、5cc、10cc和30cc體積的注射器。其他尺寸可能是

可根據要求提供。

122-39(SD)注射器用導熱環氧模貼膠

 122-39(SD)
SYRINGE DISPENSABLE THERMALLY CONDUCTIVE EPOXY DIE ATTACH ADHESIVE
DESCRIPTION: 122-39(SD) is a syringe dispensable, thermally conductive, electrically insulating, one component,
100% solids epoxy adhesive. This system features excellent thermal stability, outstanding chemical resistance and
excellent high temperature properties. Applications include adhesion to gold plated substrates and tin/lead solder
terminated components, die attach and thermal management operations, printed circuit board fabrication, advanced
material composites, sealing and high performance coatings. 122-39(SD) is a thermally conductive version of 122-
38(SD).
PROPERTIES:
Viscosity (cps) 40,000
Thixotropic Index > 2.5
 Filler Aluminum Nitride
Percent Filler 60
 Volume Resistivity, max. (?-cm) 1 X 1016
Thermal Conductivity (W/mK) 3.5
Dielectric Constant (1KHz) 4.1
Dielectric Constant (1MHz) 3.9
Dissipation Factor (1KHz) 0.027
Dissipation Factor (1MHz) 0.038
Useful Temperature Range (°C) -55 to +250
 Thermal Stability (°C) Good to +300
Die Shear Strength (psi) > 2,200 (0.09” x 0.16” die)
 Lap Shear Strength (psi) > 2,200
Glass Transition Temperature, Tg (°C) 91
Coef. Of Therm. Exp. Below Tg (ppm/°C) 75
Above Tg (ppm/°C) 233
IONIC CONTENT
Chloride <10 ppm.
Sodium <10 ppm.
Potassium <10 ppm.
(Typical properties are not intended to be used as specification limits.)
SUGGESTED HANDLING AND CURING: Material is ready to use as received. Store frozen to maintain consistent
flow properties. Allow material to warm up to room temperature before opening container. Prior to using, mix
container well to re-suspend filler if packaged in containers. Cure for 60 minutes at 150°C, or for 30 minutes at
175°C.
STORAGE: Shelf Life: < 4 days at 25°C; or 6 months at –10°C; or 12 months at –40°C.
SAFETY AND HANDLING: Use with adequate ventilation. Keep away from sparks and open flames. Avoid
prolonged contact with skin and breathing of vapors. Wash with soap and water to remove from skin.
Creative Materials, Inc.
All technical information is based on data obtained by CMI personnel and is believed to be reliable. No warranty is
either expressed or implied with respect to results or possible infringements on patents.
 REVISION DATE: 03/03/17 REVISION: E
Guidelines for Handling of Syringes
STORAGE:
• Upon receipt of shipment, syringes should be unpacked immediately and stored in freezer at -10° C. Do
not store syringes in deep freeze (-40°C).
• Do not handle syringes from the body of the packaging. Handle from the ends of the packaging.
• Store syringes vertically (upright) with tip side down. Do not store syringes horizontally (sideways).
Syringes should be stored in this manner until needed for production. Shelf life of syringes will be indicated
on the products technical data sheet.
• Syringes are labeled with product number, lot number, and manufacturing date. It is important that the
syringes are used according to earliest manufacturing date, "FIFO” (first in, first out).
PREPARING SYRINGES FOR USE:
• To thaw syringes, remove them from the freezer taking care not to handle the body of the syringe (handle
from the top and/or the tip) and allow them to acclimate to ambient temperature with the tip down.
• Do not use hands to warm syringe.
• The thawing time for each syringe will vary based on mass and composition but a minimum of 45 minutes
for 3cc, 5cc, and 10cc and a minimum of 90 minutes for 30cc syringes should be observed.
• Using a heat source to thaw syringes is not advised.
• Proximity to a heat source during thawing should be greater than 3 feet.
• Although most materials can be refrozen minimizing freeze-thaw cycles is recommended.
• Once material is fully thawed remove protective wrapping.
SYRINGE INFORMATION:
• Creative Materials syringes have luer-lock fittings and are compatible with most types of dispensing
equipment.
• Creative Materials syringe are provided packaged with smooth flow piston technology design for use on
automated or manual dispense equipment but are not hand plunger equipped.
• Creative Materials routinely provides syringes in volumes of 3cc, 5cc, 10cc, and 30cc. Other sizes may be
available upon request.